some morse code ability

src/main.rs

@@ -72,10 +72,10 @@ fn main() -> ! {
         pac.PLL_SYS,
         xosc.operating_frequency(),
         PLLConfig {
-            vco_freq: 1500.MHz(),
+            vco_freq: 1212.MHz(),
             refdiv: 1,
-            post_div1: 5,
+            post_div1: 6,
-            post_div2: 4,
+            post_div2: 1,
         },
         &mut clocks,
         &mut pac.RESETS,
@@ -112,10 +112,12 @@ fn main() -> ! {
     pwm0.set_div_frac(0);
     pwm0.clear_interrupt();
     pwm0.enable();
+    // pwm0.disable();
 
     let mut pwm_pin = pins.gpio16;
     pwm_pin.set_drive_strength(rp2040_hal::gpio::OutputDriveStrength::TwelveMilliAmps);
     pwm0.channel_a.output_to(pwm_pin);
+    pwm0.channel_a.set_enabled(false);
 
     let mut on_off_input = pins.gpio15.into_pull_up_input();
 
@@ -125,9 +127,9 @@ fn main() -> ! {
     let mut tick = 0u32;
     let mut last_input = 0u32;
 
-    let mut broadcast_on = true;
+    let mut broadcast_on = false;
 
-    let mut current_tune = 65000;
+    let mut current_tune = 4;
 
     const MAX_TUNE: u16 = 65000u16;
     const MIN_TUNE: u16 = 4u16;
@@ -157,7 +159,38 @@ fn main() -> ! {
     let mut input_mode = InputMode::default();
     let mut input_mode_chg_input = pins.gpio12.into_pull_up_input();
 
-    println!("Booted at {}MHz", pll_freq.to_MHz());
+    println!("Booted at {}kHz", pll_freq.to_kHz());
+
+    #[rustfmt::skip]
+    // CQ CQ CQ VA3FWE VA3FWE
+    let sequence = [
+        0u8,
+        2, 0, 1, 0, 2, 0, 1, 4, // C
+        2, 0, 2, 0, 1, 0, 2, 4, 4, // Q
+        2, 0, 1, 0, 2, 0, 1, 4,
+        2, 0, 2, 0, 1, 0, 2, 4, 4,
+        2, 0, 1, 0, 2, 0, 1, 4,
+        2, 0, 2, 0, 1, 0, 2, 4, 4,
+        4, // wait
+        1, 0, 1, 0, 1, 0, 2, 4, // V
+        1, 0, 2, 4, // A
+        1, 0, 1, 0, 1, 0, 2, 0, 2, 4, // 3
+        1, 0, 1, 0, 2, 0, 1, 4, // F
+        1, 0, 2, 0, 2, 4, // W
+        1, 4, // E
+        4, // wait
+        1, 0, 1, 0, 1, 0, 2, 4, // V
+        1, 0, 2, 4, // A
+        1, 0, 1, 0, 1, 0, 2, 0, 2, 4, // 3
+        1, 0, 1, 0, 2, 0, 1, 4, // F
+        1, 0, 2, 0, 2, 4, // W
+        1, 4, // E
+        0xFF, // wait before calling again
+    ];
+
+    let mut morse_sequence_index = 0usize;
+    let mut last_morse_time = 0u32;
+
     loop {
         tick = tick.wrapping_add(1);
 
@@ -201,6 +234,37 @@ fn main() -> ! {
             sh1106_dev.blit_framebuffer(&mut i2c, &mut gfx_buf);
         }
 
+        let morse_delay = match sequence[morse_sequence_index] {
+            0 => 100_000,
+            1 => 200_000,
+            2 => 400_000,
+            0xFF => 200_000_000,
+            _ => 400_000,
+        };
+
+        if tick.wrapping_sub(last_morse_time) > morse_delay {
+            morse_sequence_index = (morse_sequence_index + 1) % sequence.len();
+            last_morse_time = tick;
+
+            broadcast_on = match sequence[morse_sequence_index] {
+                0 | 4 | 0xFF => false,
+                _ => true,
+            };
+
+            match broadcast_on {
+                true => {
+                    led_pin.set_high().unwrap();
+                    pwm0.channel_a.set_enabled(true);
+                }
+                false => {
+                    led_pin.set_low().unwrap();
+                    pwm0.channel_a.set_enabled(false);
+                }
+            }
+        }
+
+        // broadcast_on = on_off_input.is_low().unwrap();
+
         if tick.wrapping_sub(last_input) < 500_000 {
             continue;
         }
@@ -221,18 +285,6 @@ fn main() -> ! {
             info!("Input Mode is now {}", input_mode);
         }
 
-        if on_off_input.is_low().unwrap() {
-            info!("Broadcast toggle");
-            last_input = tick;
-            broadcast_on = !broadcast_on;
-
-            match broadcast_on {
-                true => pwm0.enable(),
-                false => pwm0.disable(),
-            }
-            continue;
-        }
-
         if input_mode == InputMode::DisplayOnly {
             continue;
         }